Category: InP Etch

16 May

Scientific Paper on InP Microenclosure Array Fabrication Using InP Plasma Etching from Tokyo Institute of Technology

Samco 2015 Customer, Compound Semiconductor Etching, InP Etch, Microfluidics, Samco Customer Publication

Single-Cell Isolation and Size Sieving Using Microenclosure Array for Microbial Analysis

Akihiro Matsutani* and Ayako Takada1
Semiconductor and MEMS Processing Center, Tokyo Institute of Technology, 4259 Nagatsuta, Midori-ku, Yokohama 226-8503, Japan
1Biomaterial Analysis Center, Tokyo Institute of Technology, 4259 Nagatsuta, Midori-ku, Yokohama 226-8501, Japan
Sensors and Materials, Volume 27, Number 5 (2015)

Samco open-load ICP etch system was used for fabrication of micropillar fabrication on InP substrates for cell isolation and size sieving.

InP Periodic Table
For more details of our InP plasma etching capabilities, please visit the page below.
InP Dry Etching Process (RIE or ICP-RIE)

13 Oct

Scientific Paper on Fabrication of InP Photonic Crystal Waveguide from Tsinghua University, China

Samco 2013 Customer, Compound Semiconductor Etching, InP Etch, Photonic Devices, Samco Customer Publication

Fabrication of high-aspect-ratio double-slot photonic crystal waveguide in InP heterostructure by inductively coupled plasma etching using ultra-low pressure

Kaiyu Cui, Yongzhuo Li, Xue Feng, Yidong Huang and Wei Zhang
Department of Electronic Engineering, Tsinghua National Laboratory for Information Science and Technology, Tsinghua University, Beijing 100084, China
AIP ADVANCES (2013) 3, 022122

InP photonic crystal waveguide was fabricated using SAMCO ICP Etch System.

InP Periodic Table

For more details of our InP dry etching process capabilities, please visit the page below.
InP Dry Etching Process (RIE or ICP-RIE)

25 Dec

Scientific Paper on Photonic Crystal Laser Fabrication Using InP Plasma Etching by Yokohama National University

Samco 2011 Customer, Compound Semiconductor Etching, InP Etch, Photonic Devices, Samco Customer Publication

Photonic Crystal Point-Shift Nanolasers With and Without Nanoslots—Design, Fabrication, Lasing, and Sensing Characteristics

Shota Kita, Kengo Nozaki, Shoji Hachuda, Hideki Watanabe, Yuji Saito, Shota Otsuka, Takeharu Nakada, Yoshiki Arita, and Toshihiko Baba
Department of Electrical and Computer Engineering, Yokohama National University, 79-5 Tokiwadai, Hodogaya-ku, Yokohama 240-8501, Japan
IEEE Journal of Selected Topics in Quantum Electronics, (2011) 17, 6

SAMCO ICP Etch System was used for recipe optimization of InP plasma etching. InP etch profile with a high aspect-ratio was successfully fabricated.

InP Periodic Table

For our process capabilities of InP plasma etching, please visit the page below.
InP Dry Etching Process (RIE or ICP-RIE)

13 Jul

Scientific Paper on GaInAsP/InP Photonic Crystal Lasers Using InP Etching by Yokohama National University

Samco 2003 Customer, Compound Semiconductor Etching, InP Etch, Photonic Devices, Samco Customer Publication

Fabrication of GaInAsP/InP photonic crystal lasers by ICP etching and control of resonant mode in point and line composite defects

Kyoji Inoshita and Toshihiko Baba
Department of Electrical & Computer Engineering, Yokohama National University, Japan
IEEE JOURNAL OF SELECTED TOPICS IN QUANTUM ELECTRONICS (2003) 9, NO. 5, SEPTEMBER/OCTOBER

Samco ICP plasma etcher was used for InP plasma etching in GaInAsP/InP photonic crystal laser fabrication.

inp etching
For more details on our InP plasma etching technologies, please visit the process data page below.
InP Plasma Etching